Overview
Application
Seamless steel pipe for high temperature operation
ASTM A106, suitable for high temperature,It is widely used in petroleum, chemical industry, boiler, power station, ship, machinery manufacturing, automobile, aviation, aerospace, energy, geology, construction and military industry and other industries.
搜索
复制
Main Grade
Grade of high-quality carbon structural steel: GR.A,GR.B,GR.C
Chemical Component
|
Composition, % |
Grade A |
Grade B |
Grade C |
Carbon, max |
0.25A |
0.3B |
0.35B |
Manganese |
0.27-0.93 |
0.29-1.06 |
0.29-1.06 |
Phosphorus, max |
0.035 |
0.035 |
0.035 |
Sulfur, max |
0.035 |
0.035 |
0.035 |
Silicon, min |
0.10 |
0.10 |
0.10 |
Chrome, maxC |
0.40 |
0.40 |
0.40 |
Copper, maxC |
0.40 |
0.40 |
0.40 |
Molybdenum, maxC |
0.15 |
0.15 |
0.15 |
Nickel, maxC |
0.40 |
0.40 |
0.40 |
Vanadium, maxC |
0.08 |
0.08 |
0.08 |
A For each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified maximum will be permitted up to a maximum of 1.35%. |
B Unless otherwise specified by the purchaser, for each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified maximum will be permitted up to a maximum of 1.65%. |
C These five elements combined shall not exceed 1%. |
Mechanical Property
|
|
Grade A |
Grade B |
Grade C |
Tensile strength, min, psi(MPa) |
48 000(330) |
60 000(415) |
70 000(485) |
Yield strength, min, psi(MPa) |
30 000(205) |
35 000(240) |
40 000(275) |
|
Longitudinal |
Transverse |
Longitudinal |
Transverse |
Longitudinal |
Transverse |
Elongation in 2 in. (50 mm), min, %
Basic minimum elongation transverse strip tests, and for all small sizes tested in full section |
35 |
25 |
30 |
16.5 |
30 |
16.5 |
When standard round 2-in. (50-mm) gauge length test specimen is used |
28 |
20 |
22 |
12 |
20 |
12 |
For longitudinal strip tests |
A |
|
A |
|
A |
|
For transverse strip tests, a deduction for each 1/32-in. (0.8-mm) decrease in wall thickness below 5/16 in. (7.9 mm) from the basic minimum elongation of the following percentage shall be made |
|
1.25 |
|
1.00 |
|
1.00 |
A The minimum elongation in 2 in. (50 mm) shall be determined by the following equation: |
e=625000A 0.2 / U 0.9 |
for inch-pound units, and |
e=1940A 0.2 / U 0.9 |
for SI units, |
where:
e = minimum elongation in 2 in. (50 mm), %, rounded to the nearest 0.5%,
A = cross-sectional area of the tension test specimen, in.2 (mm2), based upon specified outside diameter or nominal specified outside diameter or nominal specimen width and specified wall thickness, rounded to the nearest 0.01 in.2 (1 mm2). (If the area thus calculated is equal to or greater than 0.75 in.2 (500 mm2), then the value 0.75 in.2 (500 mm2) shall be used.), and
U = specified tensile strength, psi (MPa). |
Test Requirement
In addition to ensuring chemical composition and mechanical properties, hydrostatic tests are performed one by one, and flaring and flattening tests are performed. . In addition, there are certain requirements for the microstructure, grain size, and decarburization layer of the finished steel pipe.
Supply Ability
Supply Ability: 1000 Tons Per Month Per Grade of ASTM SA-106 Steel Pipe
Packaging
In Bundles And In Strong Wooden Box
Delivery
7-14 days if in stock, 30-45 days to produce
Payment
30% depsoit, 70% L/C or B/L copy or 100% L/C at sight
Product Detail
Boiler Tube